全自动上料搅拌车具有许多优点，可大大提高生产效率。自动搅拌，省时省力;罐体可提升、旋转、升级;铰接式，方便灵活;4轮驱动，通度好;它只需要燃料消耗，不需要外部供电，对于偏远山区和无电地区的施工特别方便。成本低，维护方便。然而，随着油价的上涨，如何节约燃料消耗已经成为人们关注的问题，而作为建筑工程车辆，燃料消耗更为重要，如何降低油耗呢?
The full-automatic feeding mixer has many advantages, which can greatly improve the production efficiency. Automatic mixing saves time and labor; the tank body can be lifted, rotated and upgraded; articulated, convenient and flexible; 4-wheel drive, good connectivity; it only needs fuel consumption, does not need external power supply, and is particularly convenient for construction in remote mountainous areas and areas without electricity. Low cost and convenient maintenance. However, with the rise of oil price, how to save fuel consumption has become a concern. As a construction vehicle, fuel consumption is more important. How to reduce fuel consumption?
一、八招教你将全自动上料搅拌车的油耗降到更低
1、 Eight Tips to reduce the fuel consumption of the full-automatic feeding mixer
1.在驾驶中发现，现在搅拌器滑行距离明显缩短，这时司机应检查搅拌器轮胎压力是否达到压力标准。如果轮胎充气不足，燃料消耗会增加。提示:适当给轮胎充气。
1. During driving, it is found that the taxi distance of agitator is obviously shortened. At this time, the driver shall check whether the tyre pressure of agitator meets the pressure standard. If the tires are under inflated, fuel consumption will increase. Tip: properly inflate the tire.
2.检查全自动上料搅拌车的轮胎磨损情况，如果轮胎磨损严重，经常会出现打滑现象，增加油耗。提示:必要时更换新轮胎。
2. Check the tire wear of the full-automatic loading mixer. If the tire is seriously worn, it will often slip and increase fuel consumption. Tip: replace the tire if necessary.
3.当全自动上料搅拌车运行或启动时，如果车轮有异常噪音，应及时检查轴承和刹车系统。如果轮的转动不正常，就会影响全自动上料搅拌车的速度，从而影响燃油的消耗。提示:大修轴承和刹车系统。
3. When the full-automatic loading mixer is running or starting, if there is abnormal noise on the wheel, check the bearing and brake system in time. If the rotation of the wheel is not normal, it will affect the speed of the full-automatic feeding mixer, thus affecting the fuel consumption. Tip: overhaul the bearing and brake system.
4.搅拌器离合器打滑会造成发动机转数损失。当你发现在快速加速的搅拌器中发动机转速表增加得非常快，而速度增加得非常慢时，你就可以断定离合器打滑了。提示:需要更换离合器片、离合器片和驱动轮。
4. The clutch of agitator slips, which will cause the loss of engine speed. When you find that the engine tachometer increases very fast and the speed increases very slowly in the fast accelerating mixer, you can conclude that the clutch is slipping. Tip: the clutch plate, clutch plate and drive wheel need to be replaced.
5.当全自动上料搅拌车行驶了二三十万公里后，通常会出现缸内压力不足的现象，这时油耗会显著增加。提示:如果发生这种情况，搅拌器发动机将需要大修。
5. When the full-automatic loading mixer has been running for 230000km, the pressure in the cylinder is usually insufficient, and the fuel consumption will increase significantly. Tip: if this happens, the agitator engine will need to be overhauled.
6.当排气管冒出黑烟，燃油消耗增加时，检查化油器。提示:如果化油器太脏，将清洁剂直接喷到化油器的入口。如有黑烟，应将化油器拆开清洗。
6. When the exhaust pipe emits black smoke and fuel consumption increases, check the carburetor. Tip: if the carburetor is too dirty, spray detergent directly to the inlet of the carburetor. In case of black smoke, the carburetor shall be disassembled for cleaning.
7.如果搅拌车火花塞使用时间过长，还会出现油耗增加的现象。由于全自动上料搅拌车的火花塞损坏会降低点火能量，使汽车加速缓慢，导致油耗显著增加。提示:应更换搅拌机的火花塞。
7. If the spark plug is used for a long time, the fuel consumption will increase. Due to the damage of the spark plug of the full-automatic charging mixer, the ignition energy will be reduced, the vehicle will accelerate slowly, resulting in a significant increase in fuel consumption. Tip: the spark plug of mixer should be replaced.
8.当全自动上料搅拌车温度开关和恒温器损坏时，会有油耗的增加。由于全自动上料搅拌车的温控开关和恒温器的损坏会降低水的温度，化油器不能正常工作，导致全自动上料搅拌车的油雾化差，油耗显著增加。
8. When the temperature switch and thermostat of the full-automatic feeding mixer are damaged, the fuel consumption will increase. Due to the damage of the temperature control switch and thermostat of the full-automatic feeding mixer, the water temperature will be reduced, and the carburetor will not work normally, resulting in the poor oil atomization of the full-automatic feeding mixer, and the fuel consumption will be significantly increased.
如何减少全自动上料搅拌车的燃料消耗
How to reduce the fuel consumption of full-automatic loading mixer
二、全自动上料搅拌车在使用时注意五个事项
2、 Five points for attention when using the full-automatic feeding mixer
1. 全自动上料搅拌车应停在地上，将勺子放在地上。在发动机熄火时，需反复转动工作装置的操作手柄，确保各液压缸处于无压静止状态。当搅拌器仅停在斜坡上时，固定好轮胎。
1. The full-automatic feeding mixer shall be parked on the ground and the spoon shall be placed on the ground. When the engine is off, it is necessary to turn the operating handle of the working device repeatedly to ensure that each hydraulic cylinder is in a static state without pressure. When the mixer stops only on the slope, fix the tire.
2. 自动上料搅拌机停止工作后，操作者将各种手柄放在空挡或中间位置。
2. After the automatic feeding mixer stops working, the operator will put various handles in neutral or middle position.
3.首先取下电源锁钥匙，然后关闭电源主开关，关闭门窗。
3. First remove the power lock key, then turn off the main power switch, and finally close the doors and windows.
4、严禁将全自动上料搅拌车停在明火或高温区域，以防热爆轮胎，造成事故。
4. It is strictly prohibited to park the full-automatic loading mixer in the open fire or high temperature area to prevent the tire from thermal explosion, resulting in accidents.
5. 使用组合阀或储气罐给轮胎充气时，不得站在自动加料搅拌车的轮胎前方，以免爆炸伤到人。
5. When using combination valve or air tank to inflate the tire, do not stand in front of the tire of automatic feeding mixer to avoid personal injury caused by explosion.
山汽官方微信
2022-08-30
首页
产品
电话
置顶