In the long-term use of concrete machinery such as automatic feeding mixer, some failures will inevitably occur. At this time, we need to carry out a certain cleaning work on the mechanical soil slag. So let's take a closer look at how to clean up the soil properly.

　　1、准备应急驱动软管，关闭搅拌车，然后拆下液压马达上的高压油管接头。

　　1. Prepare the emergency drive hose, close the mixer, and then remove the high pressure oil pipe connector from the hydraulic motor.

　　2、救援车关闭，液压马达的高压油管被拆除，故障车辆上的相应连接器与应急驱动软管连接。

　　2. The rescue vehicle was closed, the high-pressure oil pipe of the hydraulic motor was removed, and the corresponding connector on the fault vehicle was connected with the emergency drive hose.

　　3、启动救援车并将其手柄转到卸货位置。故障车辆内的混凝土排出。

　　3. Start the rescue truck and turn its handle to the unloading position. Discharge of concrete from the faulty vehicle.

　　4、紧急驱动完成后，拆下驱动软管并恢复两辆车的原始状态。

　　4. After the emergency drive is completed, remove the drive hose and restore the original condition of both vehicles.
                

　　5、在滚轮和滚道之间放置一个木质楔子，以控制搅拌车的旋转。一定要注意安全。关闭发动机并拆下液压马达的高压油管。搅拌车可以自由旋转。

　　5. A wooden wedge is placed between the roller and the raceway to control the rotation of the mixer. Pay attention to safety. Shut down the engine and remove the high pressure oil pipe from the hydraulic motor. The mixer can rotate freely.

　　6、控制搅拌筒的旋转，将维护孔转到下部，然后打开维护孔清理缸内的混凝土。这时，一定要注意安全。混凝土卸料后，恢复原来的样子。

　　6. Control the rotation of the mixing drum, turn the maintenance hole to the lower part, and then open the maintenance hole to clean the concrete in the cylinder. At this time, be sure to be safe. After the concrete is discharged, the original full-automatic feeding mixer is restored.

　　全自动上料搅拌机主要适用于城市的建设，建筑的施工，是专门用来运输建筑所需的混凝并且在运输的过程中始终保持着搅拌的状态，从而保证混凝土不会凝固。那怎样能延长其使用寿命呢？

　　Automatic feeding mixer is mainly suitable for urban construction and construction, which is specially used to transport the concrete required by buildings and always keeps mixing state during transportation, so as to ensure that concrete will not set. How to prolong its service life?

　　1、对于新购入的车辆，初度运用50h支配，就该检查遍地螺栓紧固情况。包括罐体分头与减速机的连接螺栓，减速机底座与前台的连接螺栓，拖轮底座与机架的联接螺栓，以及副梁与大梁的联接螺栓等。往后要保证每月守时检查一次。

　　1. For newly purchased vehicles, the initial use of 50h control, it is necessary to check the tightening of bolts everywhere. It includes the connecting bolts between the tank split and the reducer, the connecting bolts between the reducer base and the front desk, the connecting bolts between the tugboat base and the frame, and the connecting bolts between the auxiliary beam and the main beam. In the future, we should make sure to check on time every month.

　　2、液压系统部件精度较高。尤其是搅拌车液压泵，养护简便，但恳求很高。液压油要守时更换，初度工作500h，往后2000h或起码每年更换一次，滤芯应当同时更换。加油或换油时，建议机有必要处于终止情况，否则将构成液压系统损坏。

　　2. The accuracy of hydraulic system components is high. Especially the mixer hydraulic pump, maintenance is simple, but the appeal is very high. The hydraulic oil should be replaced on time. The initial working time is 500h, and the next 2000h or at least once a year. The filter element should be replaced at the same time. When refueling or changing oil, it is suggested that the machine should be in the termination condition, otherwise the hydraulic system will be damaged.

　　3、天天行车前检查拖轮与滚道的联络面润滑油是不是干涩，应及时补偿，坚持杰出的润滑作用。每次在车辆建议之前，检查冷却器和减速机的油位，保证油位指示在目视范围内；检查液压油路的密封情况，坚 持液压系统清洁和密封，防止尘粒和水份等污染系统液压油，构成系统不能正常工作或损坏。起码每月一次整理拖轮和滚道上的污物；经过拖轮上的油嘴，向拖轮写入润滑油脂。保证转动轴起码每月润滑一次。

　　3. Check whether the lubricating oil on the contact surface of tugboat and raceway is dry and astringent before driving every day. It should be compensated in time and adhere to the outstanding lubrication function. Check the oil level of cooler and reducer to ensure that the oil level indication is within the visual range before the vehicle proposal; check the sealing condition of the hydraulic oil circuit, adhere to the cleaning and sealing of the hydraulic system, and prevent dust particles and water from polluting the hydraulic oil of the system, causing the system to fail to work normally or be damaged. Clean up the dirt on the tugboat and raceway at least once a month; write grease to the tug through the nozzle on the tug. Ensure that the rotating shaft is lubricated at least once a month.

　　4、制止对水箱随意焊接和改动，防止重物碰击；水位显现管和滤网应及时更换，防止堵塞，影响谁为分区；常常检查各种阀体是不是堵塞或是不是又工作失常，并及时进行润滑；在有结冰或许的环境中运用。

　　4. It is forbidden to weld and change the water tank at will to prevent heavy objects from hitting; the water level display pipe and filter screen should be replaced in time to prevent blockage and affect the partition; various valve bodies should be often checked for blockage or abnormal operation, and lubrication should be carried out in time; it should be used in the environment with icing.

　　以上是关于全自动上料搅拌机清理残渣及延长使用寿命的详细介绍，感谢您的阅读，希望对您有所帮助，如您想要了解更多内容欢迎点击我们的官网首页。

　　The above is a detailed introduction about cleaning residue and prolonging service life of automatic feeding mixer. Thank you for your reading and hope to help you. If you want to know more, please click our official website Home page.