大发平台大全网站-大发welcome登录入口

常见问题

热点推荐

自上料搅拌车的日常清洗过程

2022-08-30

自上料搅拌车在卸料时的注意事项有哪些？

2022-08-03

自上料搅拌车操作简单出料迅速

2022-07-06

自上料水泥搅拌车液压油箱排气管怎么加水？

2022-06-15

混凝土搅拌车轮胎偏磨是怎么回事？

2022-06-02

造成搅拌车发动机过早损坏的原因有哪些呢？

2022-06-02

关于山汽

联系人：刘老师

电话：400-879-1999

公司：山东山汽工程机械（集团）有限公司

地址：山东省莱州市206国道与308省道交叉口东南50米

为什么全自动上料搅拌机会出现高噪声高温？

所属分类：常见问题发布时间：2021-04-25 来源：浏览量：18

1.洗车水箱中的水量不足以清除。向洗车水箱注满水。

1. The water in the car washing water tank is not enough to remove. Fill the car wash tank with water.

2.如果吸管的进气口堵塞或堵塞，可以检查并拧紧吸管。不要呼吸空气。

2. If the air inlet of the straw is blocked or blocked, check and tighten the straw. Don't breathe air.

3.油箱液位过低，并且油液中的空气被吸入泵中。如果发生这种情况，您可以添加带有相同标签的液压油。

3. The liquid level of the oil tank is too low, and the air in the oil is sucked into the pump. If this happens, you can add hydraulic oil with the same label.

4.如果泵的安装支架不够牢固，则在工作期间会产生振动和噪音。在这种情况下，可以加固油泵支架。

4. If the mounting bracket of the pump is not firm enough, vibration and noise will be generated during operation. In this case, the oil pump bracket can be reinforced.

5.堵塞的滤芯会使吸油困难或不充分。在这种情况下，请清洁滤芯或更换滤芯。

5. Blocked filter element will make oil absorption difficult or insufficient. In this case, clean the filter element or
replace the filter element.
全自动上料搅拌机

6.油冷却风扇未打开。卸下：打开冷却风扇。

6. The oil cooling fan is not turned on. Remove: turn on the cooling fan.

7.如果液压油不符合要求或油太粘，请更换符合标签要求的低粘度液压油。

7. If the hydraulic oil does not meet the requirements or the oil is too viscous, please replace the low viscosity hydraulic oil that meets the label requirements.

8.储罐中有坚硬的混凝土。如果发生这种情况，请及时清理并铲起。

8. There is hard concrete in the tank. If this happens, clean up and shovel in time.

9.输入万向节轴之间的连接角度以及万向节轴与取力器之间的连接角度太大，如果松开会产生噪音，在这种情况下，请在时间内检查并拧紧。

9. The connection angle between the input cardan shaft and the connection angle between the cardan shaft and the power take-off are too large. If it is loosened, noise will be generated. In this case, please check and tighten it within time.

上一页：自动上料搅拌车车载数据的技能检查下一页：混凝土搅拌制作从未如此简单？